Indian Institute of Technology Kharagpur |

Journal

Patenting in Renewable Energy Sector- An Analysis by Khurana S., Bandyopadhyay T. K. JIPR - (Accepted/In-Press)
10. Role of Austenite Stability on Low-cycle Incremental Step Fatigue Behavior of Fe-7.5Mn-3.25Al-1Si-0.2C Medium-Mn Steel by Kumar D., Sen I. , Bandyopadhyay T. K. Materials Science and Engineering A - (Accepted/In-Press)
Highly interconnected Ti6V4Al foam with tailorable pore architecture and mechanical property by powder processing for skeletal tissue in-growth by Vaidya P. V., Seesala V. S., Talukdar R. G., Biswas A. , Jana S. , Yadav M. K., Rajshekharan R. , Dogra N. , Roy T. , Mukharjee S. , Bagade A. , Dabhade P. , Syed Z. Q., Fulzale P. , Gupta S. , Bandyopadhyay T. K., Dhara S. Advanced Engineering Materials - (Accepted/In-Press)
Comparative analysis of laser surface alloying of Ti6Al4V with FeCoCrMnTi under argon and nitrogen shielding by Rajput A., Manna I. , Bandyopadhyay T. K., Majumdar J. D. Appl. Phys. A 132 239- (2026)
Implications of the microstructure on strength-ductility synergy in a novel B2-strengthened medium manganese advanced high strength steel by Das S., Kumar S. , Pradhan S. , Bandyopadhyay T. K., Mandal S. Materials Science and Engineering A 924 127798- (2025)
Development of Iron Foams Using Different Organic Space Holders by Moon A., Thamadala N. S. , Agrawal S. , Sista K. , Dwarapudi . , Karthik . , Bandyopadhyay T. K., Misra . Trans Indian Inst Met 78 - (2025)
Influence of Relative Amount of Ni and Mn on the Cast Microstructure of Ferrite Containing Medium Mn Steels by Kumar N., Aryan A. , Bandyopadhyay T. K. Steel research international - (2025)
Microstructural characterization, formability and failure analyses of novel Ni-modified advanced high strength steel during stretch forming process by Das S., Behera D. , Rakshit R. , Panda S. K., Bandyopadhyay T. K., Mandal S. Materials Today Communications 49 114308- (2025)
Correlation between intercritical annealing duration and the tensile deformation behavior of Fe-7.5 Mn-3.25 Al-1Si-0.2 C steels: Role of austenite stability, -ferrite, and texture by Kumar D., Sanyal S. , Yadav M. K., Sen I. , Bandyopadhyay T. K. Journal of Alloys and Compounds 178506 1-15 (2025)
Correlation between intercritical annealing duration and the tensile deformation behavior of Fe-7.5 Mn-3.25 Al-1Si-0.2 C steels: Role of austenite stability, -ferrite, and texture by Kumar D., Sanyal S. , Yadav M. , Sen I. , Bandyopadhyay T. K. Journal of Alloys and Compounds 1-13 178506- (2025)
Highly interconnected Ti6Al4V foam with tailorable pore architecture and mechanical property by powder processing for skeletal tissue in-growth by Vidya P., Sessala V. , Talukder R. , Biswas A. , Jana S. , Yadav M. , Dogra N. , Roy T. , Sayd Z. , Bandyopadhyay T. K., Dhara S. Advanced Engineering Materials - (2025)
Tuning strength ductility synergy in -ferrite-containing medium-Mn steels via the TRIP effect and HDI strengthening by Kumar D., Kumar N. , Sen I. , Bandyopadhyay T. K. Journal of Materials Science 60 24589-24610 (2025)
Issues and Concern in Dissimilar Joining Including Additive Manufacturing with Specific Emphasis to Maraging Steels with other High-Strength Steels A Comprehensive Review by Behl B., Bandyopadhyay T. K. STEEL RESEARCH INTERNATIONAL - (2025)
Ultrasound-enhanced laccase pretreatment of corn stalks for sustainable biofuel production by Banerjee S., Dey S. , Bandyopadhyay T. K., Banerjee R. Biomass and Bioenergy 202 108157- (2025)
. Phase transformation and austenite stability during thermomechanical processing of high ( 5%) Al added low-density medium Mn steel by Yadav M., Kumar D. , Kumar N. , Bandyopadhyay T. K. Materialia 102360- (2025)
Understanding the TRIP effect in hot-and cold-rolled Al-added medium-Mn steels: insights into austenite stability and martensitic transformation kinetics by Kumar D., Sanyal S. , Yadav M. K., Sen I. , Bandyopadhyay T. K. Materials Today Communications 44 1-14 (2025)
Understanding the TRIP effect in hot-and cold-rolled Al-added medium-Mn steels: Insights into austenite stability and martensitic transformation kinetics, by Kumar D., Sanyal S. , Yadav M. , Sen I. , Bandyopadhyay T. K. Materials Today Communications 44 111955- (2025)
Laser welding of a novel Al added low density medium Mn steel: microstructural characterization and mechanical properties by Yadav M., Kumar N. , Kumar D. , Bandyopadhyay T. K. J Mater Sci 60 22289-222306 (2025)
Role of Solidification Behavior and Various Processing Routes on Microstructure Property Correlation in Medium Mn Steels with and without Nickel: Recent Progresses and Perspectives by Kumar N., Bandyopadhyay T. K. Steel research international 2400859- (2024)
A Systematic Review of Medium Mn Steels with an Assessment of Fatigue Behavior by Kumar D., Sen I. , Bandyopadhyay T. K. Steel research international 95 2300375- (2024)
The Effect of Post-Weld Aging Treatments on the Microstructure, Texture and Mechanical Properties of Grade 250 Maraging Steel Laser Weldments, by Mondal J., Yadav M. K., Kumar D. , Bandyopadhyay T. K. Journal of Materials Engineering and Performance - (2024)
Modulation of -ferrite formation and austenite stability in Al-added medium-Mn steels and its role in the structure property relationships by Kumar D., Yadav M. , Kumar N. , Sen I. , Bandyopadhyay T. K. Ironmaking & Steelmaking 51 658-674 (2024)
Modulation of -ferrite formation and austenite stability in Al-added medium-Mn steels and its role in the structure-property relationships by Kumar D., Yadav M. K., Kumar N. , Sen I. , Bandyopadhyay T. K. Iron Making and Steel making - (2024)
A Systematic Review of Medium-Mn Steels with an Assessment of Fatigue Behavior by Kumar D., Sen I. , Bandyopadhyay T. K. Steel Research International 95 - (2023)
Proposed Framework for Economic Development through Geographical Indication Product by Jose A., Bandyopadhyay T. K. International Journal for Legal Research and Analysis 2 - (2023)
Hot-rolled Al-added medium Mn steel (Fe-8Mn-2.85Al-1Si-0.2C): Microstructural evolution and Tensile behavior by Yadav M., Kumar D. , Kumar N. , Bandyopadhyay T. K. Materialia - 0-0 (2023)
Hot-rolled Al-added medium Mn steel (Fe-8Mn-2.85Al-1Si-0.2C) Microstructural evolution and tensile behaviour by Yadav M. K., Kumar D. , Kumar N. , Bandyopadhyay T. K. Materialia 29 101790-101799 (2023)
Multiscale precipitate evolution and its implications on the tensile deformation behavior in thermomechanically processed and peak-aged lean Mg-Al-Ca-Mn alloy by Sanyal S., Bhuyan P. , Bandyopadhyay T. K., Mandal S. Materrialia 26 - (2022)
Multiscale precipitate evolution and its implications on the tensile deformation behavior in thermomechanically processed and peak-aged lean Mg-Al-Ca-Mn alloy by Sanyal S., Bhuyan P., Bandyopadhyay T.K., Mandal S. Materialia 26 101566- (2022)
Multiscale precipitate evolution and its implications on the tensile deformation behavior in thermomechanically processed and peak-aged lean Mg-Al-Ca-Mn alloy by Sanyal S., Bhuyan P. , Bandyopadhyay T. K., Mandal S. Materials Characterization communicated - (2022)
Multiscale precipitate evolution and its implications on the tensile deformation behavior in thermomechanically processed and peak-aged lean Mg-Al-Ca-Mn alloy by Sanyal S., Bhuyan P. , Bandyopadhyay T. K., Mandal S. , Bandyopadhyay T. Materilia 26 - (2022)
Insights into the effect of different thermomechanical processing on the microstructure, phases, texture and tensile properties in Mg-0.9Al-0.6Mn-0.2Si-0.1Ca allo by Sanyal S., Bhuyan P. , Bandyopadhyay T. K., Mandal S. Intermetallics 146 - (2022)
Insights into the effect of different thermomechanical processing on the microstructure, phases, texture and tensile properties in Mg-0.9Al-0.6Mn-0.2Si-0.1Ca alloy. by Sanyal S., Bhuyan P. , Bandyopadhyay T. K., Mandal S. Intermetallics. 146 - (2022)
Detailed morphological and kinetic studies of cellulose biosynthesis from Leifsonia soli by Rastogi A., Sahoo S., Bandyopadhyay T.K., Mukherjee R., Banerjee R. Polymer 242 - (2022)
Patenting Activates in GFDM technologies An Analyics by Das S., Dey N. , Bandyopadhyay T. K., Jose A. Supremo Amicus - (2022)
Effect of microstructural evolution and texture change on the in-vitro bio-corrosion behaviour of hard-plate hot forged Mg-4Zn-0.5Ca-0.16Mn (wt%) alloy by Duley P., Bairagi D., Bairi L.R., Bandyopadhyay T.K., Mandal S. Corrosion Science 192 - (2021)
Effect of microstructural evolution and texture change on the in-vitro bio-corrosion behaviour of hard-plate hot forged Mg-4Zn-0.5 Ca-0.16 Mn (wt.%) alloy. Corrosion Science, by Duley P., Bairagi D. , Bairi L. R., Bandyopadhyay T. K., Mandal S. Corrosion Science 109860. - (2021)
Implications of annealing treatments on microstructure, texture, and tensile properties of hard plate hot forged Mg-Zn-Ca-Mn alloy by Duley P., Sanyal S. , Bandyopadhyay T. K., Mandal S. Materials Characterization 172 110885- (2021)
Implications of annealing treatments on microstructure, texture, and tensile properties of hard plate hot forged Mg-Zn-Ca-Mn alloy by Duley P., Sanyal S., Bandyopadhyay T.K., Mandal S. Materials Characterization 172 - (2021)
Microstructural evolution and its implications on the mechanical properties during age hardening in Mg-1Al-0.28Ca-0.13Mn-0.05Si alloy by Sanyal S., Gabhale O.G., Bandyopadhyay T.K., Mandal S. Journal of Alloys and Compounds 861 158540- (2021)
In situ dual matrix composite with segregated microstructure fabricated from Al TiO2 B2O3 system by mechanical thermal process by Lakra S., Bandyopadhyay T.K., Das S., Das K. Journal of Alloys and Compounds 860 - (2021)
Virus Patents in India: A Techno Legal Analysis by Mishra S., Bandyopadhyay T. K. Manupatra- Indian Legal databases - (2021)
Intellectual property issues in artificial intelligence: specific reference to the service sector by Singh N., Bandyopadhyay T. K., Bhattacharya N. S., Tewary K. Int. J. Technological Learning, Innovation and Development, 13 82-100 (2021)
Thermal conductivity of in-situ dual matrix aluminum composites with segregated morphology by Das S., Das K. , Bandyopadhyay T. K., Lakra S. Materials Research Bulletin 144 - (2021)
Thermal conductivity of in-situ dual matrix aluminum composites with segregated morphology by Lakra S., Bandyopadhyay T.K., Das S., Das K. Materials Research Bulletin 144 - (2021)
Evolution of microstructure, phases and mechanical properties in lean as-cast Mg Al Ca Mn alloys under the influence of a wide range of Ca/Al ratio by Sanyal S., Paliwal M., Bandyopadhyay T.K., Mandal S. Materials Science and Engineering A 800 140322- (2021)
Implications of grain size distribution, precipitate evolution and texture development on tensile properties in hard plate hot forged and annealed Mg Zn Ca Mn alloy by Duley P., Sanyal S., Bandyopadhyay T.K., Mandal S. Materials Science and Engineering A 784 - (2020)
Implications of grain size distribution, precipitate evolution and texture development on tensile properties in hard plate hot forged and annealed Mg-Zn-Ca-Mn alloy by Duley P., Sanyal S. , Bandyopadhyay T. K., Mandal S. Materials Science and Engineering A 784 139- (2020)
Synthesis and characterization of in-situ (Al Al3Ti Al2O3)/Al dual matrix composite by Lakra S., Bandyopadhyay T.K., Das S., Das K. Journal of Alloys and Compounds 842 - (2020)
Synthesis and characterization of in-situ (AleAl3TieAl2O3)/Al dual matrix composite by Lakra S., Bandyopadhyay T. K., Das S. , Das K. Journal of Alloys and Compounds 842 155745- (2020)
Recrystallization behaviour and tensile properties of Al-added medium-Mn-steel at different deformation-annealing conditions by Sarkar A., Sanyal S., Bandyopadhyay T.K., Mandal S. Materials Science and Technology (United Kingdom) 35 2054-2068 (2019)
Recrystallization behaviour and tensile properties of Al-added medium-Mn-steel at different deformation-annealing conditions. by Mandal S., Bandyopadhyay T. K. ,Materials Science and Technology - (2019)
Homogenization-induced age-hardening behavior and room temperature mechanical properties of Mg-4Zn-0.5Ca-0.16Mn (wt%) alloy by Duley P., Sanyal S., Bandyopadhyay T.K., Mandal S. Materials and Design 164 - (2019)
Implications of microstructure, Taylor factor distribution and texture on tensile properties in a Ti-added Fe-Mn-Al-Si-C steel by Sarkar A., Sanyal S. , Bandyopadhyay T. K., Mandal S. Materials Science and Engineering A 767 138402- (2019)
Implications of microstructure, Taylor factor distribution and texture on tensile properties in a Ti-added Fe-Mn-Al-Si-C steel by Sarkar A., Sanyal S. , Bandyopadhyay T. K., Mandal S. Materials Science and Engineering A 767 138402- (2019)
Implications of microstructure, Taylor factor distribution and texture on tensile properties in a Ti-added Fe-Mn-Al-Si-C steel by Sarkar A., Sanyal S. , Bandyopadhyay T. K., Mandal S. Materials Science & Engineering A - (2019)
Implications of microstructure, Taylor factor distribution and texture on tensile properties in a Ti-added Fe-Mn-Al-Si-C steel by Sarkar A., Sanyal S., Bandyopadhyay T.K., Mandal S. Materials Science and Engineering A 767 - (2019)
Influence of hard plate hot forging temperature on the microstructure, texture and mechanical properties in a lean Mgâ Znâ Al alloy by Sanyal S., Kanodia S., Saha R., Bandyopadhyay T.K., Mandal S. Journal of Alloys and Compounds 800 343-354 (2019)
Influence of hard plate hot forging temperature on the microstructure, texture and mechanical properties in a lean Mg Zn Al alloy by Sanyal S., Kanodia S. , Saha R. , Bandyopadhyay T. K., Mandal S. Journal of Alloys and Compounds 800 343-354 (2019)
Production of biodiesel utilizing laccase pretreated lignocellulosic waste liquor: An attempt towards cleaner production process by Gujjala L., Bandyopadhyay T. K., Banerjee R. Energy Conversion and Management 196 - (2019)
Influence of hard plate hot forging temperature on the microstructure, texture and mechanical properties in a lean Mg-Zn-Al alloy by Sanyal S., Kanodia S. , Saha R. , Bandyopadhyay T. K., Mandal S. Journal of alloy and Compounds - (2019)
Influence of hard plate hot forging temperature on the microstructure, texture and mechanical properties in a lean Mg-Zn-Al alloy by Sanyal S., Kanodia S. , Bandyopadhyay T. K., Mandal S. ournal of Alloys and Compounds 343-354 (2019)
Production of biodiesel utilizing laccase pretreated lignocellulosic waste liquor: An attempt towards cleaner production process by Gujjala L.K.S., Bandyopadhyay T.K., Banerjee R. Energy Conversion and Management 196 979-987 (2019)
Homogenization-induced age-hardening behavior and room temperature mechanical properties of Mg-4Zn-0.5 Ca-0.16 Mn (wt%) alloy by Mandal S., Bandyopadhyay T. K. Materials & Design 164 - (2018)
Harnessing Technology in Smart cities : Understanding the dynamics of technology Transfer Through FDI by Mehata C., Shankar U. , Bandyopadhyay T. K. EBC Publication - (2017)
Data protection in medical research: A comparative analysis, by Aluwalia S., Bandyopadhyay T. K. JDPP - (2017)
Enhanced strength-ductility relationship in a medium Mn high Al-alloyed multi component steel through thermomechanical processing by Sarkar A., Sanyal S. , Bandyopadhyay T. K., Mandal S. Materials Science and Engineering: A 703 205-213 (2017)
Influence of annealing parameters on phase evolution and recrystallization kinetics of a Mn-Al-Si alloyed duplex steel by Bandyopadhyay T. K., Mandal S. , Sarkar A. , Sanyal S. Materials Characterization 134 213-224 (2017)
Kinetic Modeling of Laccase Mediated Delignification of Lantana camara by Lohit K Srinivas Gujjala,,Tapas K Bandyopadhyay and Rintu Banerjee Bioresource Technology accepted - (2016)
Characterization of Microstructure and Mechanical Properties of 9.2Cr0.45V0.7C Heat Resistance Steel by A. Mandal, K Guguloth, T K Bandyopadhyay Metallography Microstructure and Analysis 5 - (2016)
Low Carbon Technologies for Our Cities of Future: Examining Mechanisms for Successful Transfer and Diffusion by Mehta C., Bandyopadhyay T. K., Shankar U. India Quarterly 72 1-13 (2016)
Harnessing Technology in Smart cities : Understanding the dynamics of technology Transfer Through FDI by Mehta C., Bandyopadhyay T. K., Shankar U. GNLU Journal of Law, Development and Politics, 6 1-20 (2016)
Microstructure Characterization and Mechanical Properties of Modified 9Cr Steel by Mandal A., Bandyopadhyay T. K. Steel Research International - (2016)
Effect of tempering on microstructure and tensile properties of niobium modified martensitic 9Cr heat resistant steel by A. Mandal, and T.K.Bandyopadhyay Materials Science and Engineering, 620 - (2014)
Applicability of doctorine of equivalent and prosecution history estoppels in Indian patent system by Bandyopadhyay. T and Singharoy .T Int.Journal of Intellectual Property Management 10 - (2012)
Managing Competition: Scrutinising the Indian Patent Act 1970 by Dr. T.K.Bandyopadhyay and Saurabh Bindal European Competition Law Review 33 - (2012)
Nanomaterials and Effects on Biological Systems:Development of Effective Regulatory Norms by Padmavati Manchikanti & Tapas K. Bandopadhyay Nanoethics DOI 10.1007/s11569-0 - (2010)
Synthesis and Characterization of TiC-reinforced austenitic matrix composites by T. K. Bandyopadhyay, and K. Das J. of Materials Science Letters 40 5007-5010 (2005)
Synthesis and characterization of TiC-reinforced iron-based composites Part I: on synthesis and microstructural characterization by T. K. Bandyopadhyay, K. Das and S. Chatterjee Journal of Materials Science 39 5735-5742 (2004)
Indentation Response of Plasma Sprayed Ceramic Coatings by Ghosh S., Bandyopadhyay T. K., Das S. , Bandyopadhyay P. P. J Mter. Sci. 38 1565-1572 (2003)
Processing and Characterization of Plasma-Sprayed Ceramic Coatings on Steel Substrate: Part II; On Coating Performance by Das S., Bandyopadhyay P. P., Ghosh S. , Bandyopadhyay T. K., Chattopadhyay A. B. Met. & Mat. Trans. A 34 1919-1930 (2003)
Processing and Characterization of Plasma-Sprayed Ceramic Coatings on Steel Substrate: Part I; On Coating Characteristics, by Das S., Bandyopadhyay P. P., Ghosh S. , Bandyopadhyay T. K., Chattopadhyay A. B. Met. & Mat. Trans A 34 1909-1918 (2003)
A Review of the synthesis of Fe-TiC composites by K. Das, T. K. Bandyopadhyay, and S. Das Journal of Material Science 37 2881-2892 (2002)
Application of Differential Scanning Calorimetry (DSC) kinetic Methods to Determine the Kinetic Parameters of a Precipitation in a 60/40 Brass by K. Das and T. K. Bandyopadhyay Scripta Metallurgica et Materialia 44 2597-2603 (2001)

Patent

Graded material comprising welded dissimilar materials including aluminium (Al) added low density medium Mn steel and maraging steel, system and method of its welding by Yadav M., Kumar D. , Kumar N. , Bandyopadhyay T. K. - (2025)
IMPROVED SINTERING PROCESS FOR POWDER WITH HIGH OXIDATION RISKS by Vaidya P., Dhara S. , Bandyopadhyay T. K. - (2025)
High strength Al-added medium-Mn steel by Kumar D., Sen I. , Bandyopadhyay T. K. - (2024)
High strength Al-added medium-Mn steel by Kumar D., Yadav M. , Bandyopadhyay T. K. - (2024)
Improved Sintering Process For Powder With High Oxidation Risks by Vaidya P., Dhara S. , Bandyopadhyay T. K. - (2024)
In situ aluminum based dual matrix composites with enhanced thermal conductivity by Das K., Lakra S. , Bandyopadhyay T. K., Das S. - (2024)
Ni modified low alloy high strength steel and a process to produce the same by Kumar S., Sarkar A. , Nayak D. , Mandal S. , Bandyopadhyay T. K. - (2024)
A formulation for silver electroplating by Das S., Das K. , Bandyopadhyay T. K., Satpathy B. , Jena S. - (2024)
An improved thermomechanical approach for an admirable strength-ductility combination in Al-added medium-Mn steel for automotive applications by Kumar D., Yadav M. K., Sen I. , Bandyopadhyay T. K. - (2024)
An improved thermomechanical approach for an admirable strength-ductility combination in Al-added medium-Mn steel for automotive applications by Kumar D., Yadav M. , Sen I. , Bandyopadhyay T. K. - (2024)
Dense-Porous Structures And Its Process Of Manufacture by Vaidya P., Dhara S. , Bandyopadhyay T. K. - (2024)
Graded material comprising welded dissimilar materials including aluminium (Al) added low density medium Mn steel and maraging steel, system and method, of its welding by Yadav M., Bandyopadhyay T. K. - (2024)
Nickel added medium Mn steel by Das S., Mandal S. , Bandyopadhyay T. K. - (2023)
Nickel Containing Medium Mn steel by Das S., Bandyopadhyay T. K., Mandal S. - (2023)
Nickel-modified medium manganese advanced high strength steel with improved processing routes for automobile applications by Das S., Mozumder Y. H., Bandyopadhyay T. K., Mandal S. - (2023)
Nickel-modified medium manganese advanced high strength steel with improved processing routes for automobile applications by Das S., Mozumder Y. H., Bandyopadhyay T. K., Mandal S. - (2023)
Ni MODIFIED MEDIUM mMn STEEL FOR AUTOMOBILE APPLICATION by Das S., Bandyopadhyay T. K., Mandal S. - (2023)
Personal Protective equipment for breathing of purified air through smart multimodal purification units by Dhara S., Bandyopadhyay T. K., Das Bhattacharya S. , Vaidya P. V. - (2021)
Multimodal air purifier and disinfectant for indoor and outdoor settings: Design, Development, testing and Application thereof by Dhara S., Bandyopadhyay T. K., Vaidya P. V., Kedia N. , Mondal A. , Mandal S. M. - (2020)
A Process for the Production of Ferrous Based Composite Materials. No.233871, Granted by Das K., Bandyopadhyay T. K. - (2009)

Book Chapter/Section

Legal Trends in Ethical Dimensions of Biodiversity Conservation by Jose A., Bandyopadhyay T. K. Biological Diversity: Mapping Horizon - (2023)
Foodstuffs and Geographical Indications in India: An analysis by Manchikanti P., Datta S. , Bandyopadhyay T. K. Geographical Indication Protection in India: The Evolving Paradigm - (2021)

Workshop

Evolutionary Aspects of Traditional Medicinal Knowledge from the Multilateral Perspective by Jose A., Bandyopadhyay T. K., Padmavati M. FOURTH IP & INNOVATION RESEARCHERS OF ASIA (IPIRA) CONFERENCE - (2022)

Conferences

Correlation between microstructure and tensile properties in a novel lean as-cast Mg-0.8Al-0.3Ca-0.4Mn alloy by Sanyal S., Bandyopadhyay T. K., Mandal S. 58th National Metallurgists Day and 74th Annual Technical Meeting of Indian Institute of Metals (NMD-ATM 2020) - (2021)
Synthesis and characterization of in-situ (AleAl3TieAl2O3)/Al dual matrix composite by Yadav M., Bandyopadhyay T. K. National Online Conference on Research and Developments in Material Processing, Modelling and Characterization 2020 - (2020)
Friction stir welding of similar and dissimilar metals: A Review by Yadav M., Bandyopadhyay T. K. Research and Developments in Material Processing, Modelling and Characterization 2020 (RDMPMC-2020) - (2020)
Structure-property relationship in a thermomechanically processed Mg-Zn-Al alloy by Sanyal S., Kanodia S. , Saha R. , Bandyopadhyay T. K., Mandal S. European congress and exhibition on advanced materials and processes (EUROMAT 2019) - (2019)
Development and characterization of Mg-4Zn-0.5Ca-0.16Mn alloy for biomedical applications by Bandyopadhyay T. K., Mandal S. TMS 2018 Annual Meeting & Exhibition, The Minerals, Metals & Materials Society (TMS), Phoenix, Arizona, USA. - (2018)
Evaluation of indigenous alumina and zircon powders for potential application as plasma sprayable consumables by Das S., Bandyopadhyay T. K., Bandyopadhyay P. P., Ghosh S. , Chattopadhyay A. B. Advances in surface treatment: research and applications' ( ASTRA-2003) 512-520 (2003)

Book

Intellectual Property for Engineers by Bandyopadhyay T. K., Bindal S. - (2015)

Metallurgical and Materials Engineering

Faculty

Tapas Kumar Bandyopadhyay

Responsibilities

Research Areas

Principal Investigator

Co-Principal Investigator

Ph. D. Students

Abhinay Rajput

Anindya Khamaru

Bharat Behl

Navanit Kumar

Omkar Jagadish Sahu

Shikha Priyadarshini

Shiuli Chakraborty

Supriya Mondal